Render and Cladding Cleaning Cost in the UK: What Goes Into the Price (2026)

Render cleaning cost is set by wall area, height, access, render type and how bad the growth is, so a price you can trust comes from photos of your house, not a rate card. Neither the render makers nor we publish a flat figure. What we can show you is every checkable number that goes into one.
Most cost guides for this job lean on figures from quote sites, and we've left those out. Everything below comes from a hire firm, a council, a render maker or gov.uk, with the source under each table, so you can check it yourself and see what's left once the kit is paid for: somebody's time, skill and risk.
At a glance
| Question | Short answer |
|---|---|
| Is there a standard price per m²? | Not from the makers or from us. Quotes are built from photos and the factors below |
| What moves the price most? | Wall area, height and access, render type, how far the growth has gone, and what else is done in the same visit |
| Published hire rate for a cherry picker | One firm's self-drive rates start at £130 a day, ex VAT |
| Published hire rate for a tower | One firm lists a 5.8m handrail-height tower at £89.61 a week, ex VAT |
| Council fees if scaffold stands on the pavement | Enfield: £200 application plus £37 per m², minimum £370, for each 30 days. Camden: £464.80 for minor works up to £1,548.16 for major works, each with a deposit |
| Parking bay for the kit | Barnet: £69.63 per bay per day, plus a £171.39 admin fee |
| Cleaning product | One merchant lists a 5 litre pack of K Rend Algae Clean at £45.04 ex VAT |
| Pressure washer on render | K Rend says fan setting, not high power. Weber says pressure washing is unsuitable for dry dash |
| How long a clean lasts | Usually two to three years on render and brick. Shaded north walls under trees go green sooner |
| Cladding | Priced on panel type, height, method statement and paperwork. Cleaning is not remediation |
| VAT | 20% standard rate, where the cleaner is VAT registered |
Why is there no single price for cleaning render?
The wall itself is a small part of the price. Most of it is everything around the wall. Two houses with the same area of render can cost very different amounts to clean if one is reached from the ground and the other needs a tower, a licence and a parking bay.
We haven't published an exterior price at Techno Clean, and we don't think anyone can honestly do it from a desk. Our quotes come from photos. That's why this guide shows you the building blocks instead of a made-up total.
One block applies to everything: tax. The standard VAT rate is 20% on most goods and services, and if the company you hire is VAT registered it goes on the invoice. Ask every cleaner whether the figure they give you includes it, because VAT adds 20% to the figure.
What drives the price of cleaning render?
Six things move the number: how much wall there is, how high it goes, how anyone gets up to it, what the render is, how far the growth has gone, and what else gets done on the same visit.
- Area in m². More wall means more time and more product. Measure each elevation (height times width) and take off the windows and doors. A semi with a rendered front and a flank wall is a very different job from a fully rendered detached house.
- Storeys and access. A ground-floor wall and a three-storey gable are different jobs, not the same job at different prices. We go into the kit and its published costs below.
- Render type. Monocouche, silicone render, K Rend, painted sand and cement and dry dash all behave differently. Silicone render, monocouche, K Rend and London stock brick all come up well with soft washing, but dry dash needs extra care because Weber says pressure washing is unsuitable for dry dash finishes, while Sika allows a limited pressure wash on its own (more on that below).
- How far the growth has gone. A light green film is one visit. Thick growth that has been there for years may need a second application, which the Algae Clean data sheet allows for on heavily soiled areas.
- Where the wall faces and what's near it. Weber says north-facing elevations are more likely to get algae because they're cooler and damper. Trees, a damp garden or a leaking gutter make it worse, and a leak needs fixing or the stripe comes back.
- What else is done in the same visit. Most people book the whole outside of the house in one go: walls, fascias and soffits together. Doing them together means the access kit goes up once.
In an occupied block, add working around residents, shared entrances and parking. That takes longer than a single house with a driveway, and it's the reason block and managing agent quotes need more detail up front.
If you'd like the method before the money, we've covered it in how to clean render without wrecking it.
What does the cleaning product cost?
The product is the smallest line in a render clean. One merchant, Elliotts, lists a 5 litre pack of K Rend Algae Cleaner at £45.04 ex VAT (£54.05 inc VAT) at the time of writing, 7 November 2026. Here's what the data sheet says that pack does. The maker's sheet calls it Algae Clean; the merchant's listing has the same size and the same 2 to 5 m² per litre coverage.
| Item | What the data sheet says |
|---|---|
| What it is | Water-based, anti-bacterial fungicidal concentrate wash for moulds, algae and lichens |
| Normal dilution | 1 part Algae Clean with 2 parts water |
| Heavy contamination | 1 part Algae Clean with 1 part water |
| Application rate | 2 to 5 sq metres per litre of diluted material, depending on the surface |
| Pack size | 5 litres |
| Re-treatment | "should be applied regularly (every 6 to 12 months)" to aid prevention of immediate re-infection |
| Before you start | Trial on an inconspicuous area. Scrape off heavy build-up. Apply onto a dry background |
| Heavily soiled areas | A second application may be required |
Source: K Rend (Kilwaughter Minerals), Algae Clean Technical Data Sheet (PDF, hosted by merchant Rowebb)
Do the sums on the normal mix and one 5 litre pack makes 15 litres of wash. At 2 to 5 m² per litre, that covers 30 to 75 m². So on the normal mix the product works out at roughly 60p to £1.50 per m² ex VAT for that one brand. On the heavy-contamination mix (1 part to 1 part water) a pack makes 10 litres and covers 20 to 50 m², which is about 90p to £2.25 per m². Both leave out wastage. That's the scale of the line, not what any particular cleaner uses, because contractors pick their own products.
Weber sells its own render cleaner, and its data sheet reads differently.
| Item | What the data sheet says |
|---|---|
| What it is | Water-based algae and fungi cleaner, supplied ready for use in 5 litre and 25 litre bottles |
| Coverage | Approximately 10 m² per litre, and the maker says this "will vary according to the type of surface involved and method of application" |
| Application | Drench apply. For large areas, a pressurised knapsack or garden sprayer is best |
| Dwell time | Left for a minimum of 48 hours to take effect |
| Afterwards | Dead growth removed by brushing with a stiff bristle or wire brush, "or alternatively by power washing" |
| Weather | Not in rain, and not below 5°C or above 30°C, or if those are likely within 24 hours |
Source: Weber, weber CL150 technical data sheet (PDF)
That 48-hour dwell is worth knowing about. It's the maker's minimum for its own product, and it shows why a render clean that kills the growth isn't a ten-minute rinse.
How much does access add?
Access is the line that changes most from building to building, because the kit you need depends on how high the render goes. The Health and Safety Executive's first instruction is to do as much work as possible from the ground, and it says ladders are only for light work of short duration, with a maximum of 30 minutes at a time.
Where the work can't be done from the ground, the next step up is a tower. Speedy Hire publishes this rate for one.
| Item | Published rate (ex VAT) |
|---|---|
| BoSS Standard 2.5m tower, 5.8m handrail height, one week | £89.61 |
| Each extra day | £17.92 |
Source: Speedy Hire, BoSS Standard 2.5m Tower 5.8m Handrail Height
Higher or harder to reach, a cherry picker (the industry calls it a mobile elevating work platform) takes over. Smart Platforms publishes its self-drive rates.
| Model | Working height, up to | First day (ex VAT) |
|---|---|---|
| Z10 | 10.8 to 11.4m | £130 |
| V12 | 12.5 to 13.8m | £151 |
| S18 | 17.9 to 18.2m | £214 |
| Z20 | 20 to 21m | £239 |
| S27 | 27m | £329 |
Source: Smart Platforms, Cherry Picker Hire Prices
Four notes from that page. All prices are plus VAT, and the day columns are running totals, so a Z10 is £130 for one day, £220 for two and £396 for four, with the fifth day free. A collision damage waiver is charged at £53 per day (£72 for the S27) if required, and you need an approved Smart Platforms account to hire. For an operated hire, the firm says to call for a quote, so there's no published rate for that.
Do you need scaffolding, and what do councils charge?
If a wall can't be reached safely from a tower or platform, scaffold goes up. Where it stands on a public road or pavement, or hangs over one, the council wants a licence, and the licence has a price. The scaffolder's own charge for erecting it isn't published anywhere we could verify, so we haven't put a number on it.
Here are three London councils. They don't charge in the same way, which is the point.
Enfield charges by the area of highway the structure covers.
| Type | Fee |
|---|---|
| Application fee (non-refundable) | £200 |
| Licence fee, up to 30 days (min £370 to max £3,700) | £37 per m² |
| Renewal, each 30-day period (min £370 to max £3,700) | £37 per m² |
| Refundable deposit, up to 10 m² | £500 |
| Refundable deposit, each additional m² | £50 |
Source: Enfield Council, Cranes, scaffolding, hoarding and projection
Camden uses three bands of building licence, each with a deposit.
| Band | Licence fee | Deposit |
|---|---|---|
| Minor works | £464.80 | £785.56 |
| Standard works | £711.50 | £1,702.09 |
| Major works | £1,548.16 | £4,582.58 |
Camden says licences last a maximum of 6 months, a two month extension costs £172.81, and each site inspection costs £77.47.
Source: Camden Council, Building licence
The kit may also need somewhere to park. Barnet gives building works, including hoarding and scaffolding, as one of the reasons for a parking bay suspension.
| Item | Barnet charge |
|---|---|
| Daily rate | £69.63 per bay per day (a 5 metre length) |
| Administration fee | £171.39 per successful application, non-refundable |
Source: Barnet Council, Parking suspensions and dispensations
On the Hertfordshire side, Hertfordshire County Council publishes standard conditions for any structure on the public highway. They include lighting between half an hour before sunset and half an hour after sunrise, a 1.2m clear walkway on the footway, and public liability insurance of at least £10,000,000 held by the applicant. That page lists no fee, so we haven't quoted one.
None of this applies to scaffold on your own drive or garden, because the councils' rules cover structures on or over the public highway.
What would the published inputs add up to?
Here's an illustration, not a quote and not a Techno Clean price, and it leaves out the biggest cost of all. We've assumed 100 m² of rendered wall to clean, and, for the scaffold line, 10 m² of licensed pavement. Every figure in the middle column comes from a source above, and the product lines use the normal mix.
| Line | Published figure | Notes |
|---|---|---|
| Algae Clean for 100 m² | £90.08 to £180.16 ex VAT | 2 to 4 packs at £45.04. 100 m² needs 20 to 50 litres of wash, a third of that is concentrate (6.7 to 16.7 litres), and packs are 5 litres |
| Tower, one week | £89.61 ex VAT | Speedy Hire rate |
| Cherry picker, one day | £130 ex VAT | Smart Platforms Z10, plus £53 collision damage waiver if required |
| Enfield scaffold licence, 10 m² | £570 | £200 application plus £370 (£37 times 10 m², which is also the minimum) |
| Enfield deposit, 10 m² | £500, refundable | Returned if the road and pavement aren't damaged |
| Product plus tower | £179.69 to £269.77 ex VAT | The first two lines added together |
| Product plus cherry picker, one day | £220.08 to £310.16 ex VAT | The first and third lines added together |
Source: arithmetic on the Algae Clean, Elliotts, Speedy Hire, Smart Platforms and Enfield Council figures above.
Now look at what isn't in that table: any person. There's no day's work, no insurance, no travel, no rinse water, no waste handling, no second visit if a patch needs another coat, and no VAT. That's why we'd rather look at your wall than hand you a number. A figure that skips those lines is a cost of materials, not a price.
Soft washing or pressure washing: what do the makers say?
Makers allow water on render, within limits: low pressure, a fan spray instead of a jet, a mild detergent, and on some finishes, skip the pressure washer altogether. Weber's guide tells you to wash with a pressure washer and a mild detergent, adjusted to a fan action rather than a jet, and adds: "Pressure washing is unsuitable for dry dash finishes."
K Rend's aftercare guide is the same in spirit.
| Topic | What K Rend says |
|---|---|
| How often | "Cleaning the render is generally advised after a few years" |
| Method | A pressure washer with clean water and a low concentration of mild detergent |
| Setting | Washer "set on fan application, not high power" because "very high pressure washers can damage the render surface" |
| Direction | Carefully, in a controlled fashion, working from top to bottom |
| Algae | Use a biocide or algaecide such as K Rend Algae Clean |
| Cracks | Leave as long as possible to stabilise before any repair |
Source: K Rend, Aftercare and Maintenance Guide (PDF)
So where does soft washing fit? It's the low-pressure end of that advice, taken seriously. A treatment that kills algae, mould and green growth at the root, applied at low pressure, instead of forcing water behind the finish. That's what we do for render, and here's how soft washing works if you want the detail.
How long does a clean last, and what does that cost per year?
On render and brick, a soft wash usually stays clean a good two to three years. North-facing walls under trees go green again faster, because the growth needs damp and shade to come back. K Rend's guide takes a similar view, saying cleaning is "generally advised after a few years", and adds that "The presence of algae will not adversely affect the long term performance of the render", so a clean is about looks rather than urgency. Weber's render cleaning advice sits in between at "once a year or as often as necessary", and the Algae Clean data sheet above goes further and suggests re-applying every 6 to 12 months to slow re-infection.
The maths for cost per year is simple. Divide the price of the clean by the years it holds. If a clean lasts three years instead of two, the same bill costs a third less per year. That's why a cheaper quote that only knocks the surface green off can cost more over time than one that treats the growth at the root.
It also shows why the cause matters. If a gutter is dripping onto one stripe of wall, you'll be cleaning that stripe every year until it's fixed. Fix the water first.
When does render need repair or repainting instead of cleaning?
When the problem is the surface itself: cracks, blown patches, lost texture or stains that won't lift. Cleaning takes off growth and weathering film. It doesn't rebuild render.
Sika is blunt about this in its maintenance guide for Sikatherm and Parextherm dry dash systems:
- If a stain can't be removed, "it may be necessary to seal and re-coat the surface".
- Painting changes things: applying its paint neat "will alter the texture and sheen of the original finish", so do a trial area first.
- Repairs show: "any repair to a render finish will be seen", and if a wall has to be refinished, it may be best to re-render the whole wall.
- Pressure has limits. For general soiling on its own dry dash systems, Sika allows a pressure wash at a maximum of 1000psi, with the nozzle no closer than 300mm from the surface, and says not to concentrate the nozzle in one area as this may damage it. It also says "We recommend you carry out a trial area first".
That last point is the cost of getting it wrong. A patch you have to re-render, or a wall you have to repaint to hide a damaged face, costs more than the clean you were trying to save on. If the photos show cracking or blown render, a renderer should look at it before any cleaning goes ahead.
What does cladding cleaning cost, and why is it priced differently?
Cladding is priced on the panel, the height and the paperwork, not on how green the wall is. The same wall area can cost very different amounts depending on the finish, how high it is, how it's reached and what the building manager needs on file.
We clean cladding with low pressure and chemistry matched to the panel. That covers composite, aluminium, powder-coated and anodised finishes, uPVC, timber, render panels, curtain walling, fascias, soffits and signage. What changes the price:
- Access. Where the elevation allows, we work from ground level with a reach pole and a fed water system. Otherwise the job needs a powered access platform or a cradle. We say so in the survey and price it honestly.
- Paperwork. Managed buildings get a method statement and risk assessment. Work at height is planned around the Work at Height Regulations 2005.
- Order of work. Gutters and fascias first, then the elevation, then the glass. The glass is cheaper in one visit.
- Frequency. Every two to three years suits most London buildings, and sooner by main roads and railways.
We quote it as a one-off or a periodic visit, not a contract.
Cladding makers are strict about what touches their panels, and that's the other reason it isn't priced like render. Rockpanel's cleaning instructions are a good example.
| Topic | What Rockpanel says |
|---|---|
| Inspection | An annual visual inspection of the facade's appearance and stability |
| Cleaning agents | Clean water, or mild products similar to those used for washing a car |
| pH | "Do not use cleaning agents with a high or low pH value" |
| Solvents and abrasives | Solvent-based, abrasive or aggressive agents can cause irreparable damage |
| Pressure | "The use of high-pressure water devices ... is not recommended" |
| Temperature | Do not clean below 5°C, and avoid direct sunlight and hot temperatures |
| Method | Test first, clean the whole facade from top to bottom, then rinse with clean water |
Source: Rockpanel (Rockwool Group), Cleaning instructions (PDF)
Coated aluminium has its own rules. The Qualicoat care guide covers powder-coated architectural aluminium, such as curtain wall panels, spandrels and window frames.
| Topic | What Qualicoat says |
|---|---|
| Test first | A small, inconspicuous area, to make sure no colour change or damage arises |
| Cleaning | A soft brush or non-abrasive cloth with a neutral mild household or car wash detergent |
| Rinse | Thoroughly, with fresh water |
| Never | Steel wool, scrapers, sandpaper, scouring liquids or powders. Strong solvents, alkaline or acid cleaners |
| Water | Hard water is not recommended, because it can stain the coating |
| Heat | Do not clean a surface that is hot from direct sunlight |
| Frequency | At least once a year in a normal environment. Every 3 months in a marine or industrial one |
Source: Qualicoat, Recommendations for the care of coated aluminium (PDF)
Notice the gap on frequency: Qualicoat says coated aluminium wants a wash at least yearly in a normal environment, and every 3 months in a marine or industrial one. For cladding as a whole, every two to three years suits most London buildings. If your panels are coated aluminium, follow the coating body's guidance for the aluminium and tell us at survey.
One more thing, and it matters for managing agents. Cleaning is not remediation. The government's guidance defines cladding remediation, for the purposes of leaseholder protections in the Building Safety Act, as the removal or replacement of any part of a cladding system that forms the outer wall of an external wall system and is unsafe. We're cleaners, not cladding surveyors: no EWS1, no fire assessment, no remediation. If you suspect a problem with the panels themselves, that needs a qualified assessor.
How do you get an accurate render cleaning quote?
Send photos of every elevation, say how high the building is, and say where a platform or tower could stand. That's enough for us to quote from, and it's the same information any careful cleaner will want.
- One photo of each elevation, taken far enough back to show the eaves down to the ground.
- A close-up of the worst patch. It shows whether it's a light film or thick growth.
- The number of storeys, and anything that complicates the height, like a bay, an extension roof or a dormer.
- The render type, if you know it. The paperwork from the original job often names it. K Rend, silicone, painted and dry dash all differ.
- Access. A side passage, gate width, soft or sloping ground, and where the van can park. If anything would have to stand on the pavement or road, say so, because that's where a licence or a bay suspension comes in.
- What else you want done. Gutters and fascias, soffits and the roof are often cheaper to do when the access kit is already up.
- Any leaks or damp patches. Water ruins a clean.
When you compare quotes, ask each one the same questions. How will they reach the top of the wall? Who pays for a licence or a bay suspension? What product and dwell time? Is VAT included? Are fascias and soffits in the price? Two quotes that look different are often quoting different jobs.
What mistakes make render cleaning cost more?
Most of them come down to doing the cheap thing first and paying for it later.
- Using a pressure washer on a high setting. The makers above all set limits. Go past them and you risk damaging the surface, and a repair won't match, as Sika says.
- Cleaning before the leak is fixed. Weber's data sheet says growth can point to damp conditions. If water keeps running down the wall, the green comes back.
- Skipping the trial patch. The Algae Clean data sheet, Sika, Rockpanel and Qualicoat all ask for a test on a hidden area. A colour change on a visible wall can't be undone by cleaning.
- Treating cladding like render. Rockpanel says the wrong pH or a solvent causes irreparable damage. Rockpanel calls it irreparable, and a re-clean won't fix that.
- Booking the bay suspension late. Camden says parking bay suspensions should be booked at least 17 days ahead, and a later booking may incur a short notice charge, which it lists as £349.81. That's more than a week of tower hire at the Speedy Hire rate above.
When to get help
Get a quote when the render is out of reach from the ground, when growth is thick or keeps returning, or when you're a managing agent who needs a method statement. We can't tell you a number from here, but we can tell you what the job involves.
We do soft washing for render and brick, and most people book the whole outside of the house in one go: walls, fascias and soffits together. Send photos on WhatsApp and we'll tell you what we'd need to see on site. If the photos show cracked or blown render, that needs a renderer first.
Frequently asked questions
How much does it cost to clean render? There's no honest flat rate, and we haven't published one. The price depends on area, height, access, render type and how far the growth has gone. The tables above show the published figures that feed into it, and a quote from photos is the only way to get the real number.
How much does it cost to clean render per m²? Nobody we can cite publishes a per-m² labour rate. The only per-m² figures we can source are for product: K Rend's Algae Clean covers 2 to 5 m² per litre of diluted wash, and Weber's CL150 covers about 10 m² per litre. On the Elliotts price, Algae Clean works out at roughly 60p to £1.50 per m² ex VAT on the normal mix (90p to £2.25 on the heavy mix), before any labour, wastage or access.
Is soft washing cheaper than pressure washing? We can't give you a price comparison that holds for every house. What's documented is the risk: makers limit pressure on render, and Sika says any repair to a render finish will be seen. A pressure wash that damages the render is not a saving.
Do you need scaffolding to clean render? Not always. The HSE says to do as much work as possible from the ground, and a tower or cherry picker often does the job. Scaffold is for walls that can't be reached safely that way, and it needs a council licence if it stands on or overhangs the highway.
How often should render be cleaned? K Rend says generally after a few years, and Weber says once a year or as often as necessary. On render and brick, a soft wash usually stays clean a good two to three years, and north-facing walls under trees go green sooner.
Do I have to pay VAT on render cleaning? The standard rate is 20% on most goods and services. A cleaner only has to charge it once they're VAT registered, which the government says is required when taxable turnover goes over £90,000. Ask for the figure with and without VAT, so you can compare like with like.
Does cleaning cladding count as remediation? No. For the leaseholder protections in the Building Safety Act, the government defines cladding remediation as removing or replacing an unsafe part of a cladding system that forms the outer wall of an external wall system. We clean. We don't do EWS1, fire assessments or remediation.
Get a free, no-obligation quote, call 07375 104665, or WhatsApp wa.me/447375104665. We cover North London and the Hertfordshire borders.
Last updated: 7 November 2026
About Techno Clean: a London deep-cleaning company covering North London and the Hertfordshire borders. We specialise in one-off deep cleans for homes, landlords, builders and businesses, fully insured with £5 million public liability cover, with more than 500 jobs completed.




