How to Clean LVT and Vinyl Flooring (and What Ruins It)

The best way to clean LVT and vinyl flooring is to sweep or dust mop the grit up most days, then damp mop about once a week with a pH-neutral cleaner made for vinyl, diluted exactly as the label says. No steam mop, no abrasive pads, no vinegar. Good LVT floor cleaning is mostly about not overdoing it.
At a glance
| Question | Short answer |
|---|---|
| Day to day | Sweep or dust mop. Grit is what scratches the surface |
| Mopping | Damp, not wet, with a pH-neutral vinyl cleaner at the label dilution. Amtico suggests weekly |
| Steam mops | No. Karndean, Amtico and Forbo all advise against them |
| Bleach | Depends on the brand. Karndean says avoid it, Amtico allows 1 part bleach to at least 10 parts water |
| Vinegar | Amtico says no, because the acidity can dull the surface |
| Doormats | Check the backing. Amtico says rubber-backed mats can permanently stain LVT |
| Deep clean | Once or twice a year with the maker's own remover or stripper, then a rinse |
| Dull, grey or sticky floor | Can be a film of old cleaner rather than dirt. Try a clean-water rinse first |
| Things cleaning won't fix | Worn-through pattern, deep scratches, rubber mat stains |
A lot of what's on the makers' "don't" lists comes down to overdoing it. Below is what Karndean, Amtico and Forbo say in their own care guides, including where they flatly disagree.
What is LVT, and why does it change how you clean it?
LVT, or luxury vinyl tile, is a layered vinyl floor: a printed design under a clear wear layer, with a protective coating on top. You're not really cleaning vinyl. You're cleaning that coating, and the job is to keep grit and residue off it without wearing it away.
Karndean's explanation of what its LVT is made of lists five layers, ending with "one clear PVC embossed wear layer and a top polyurethane (PU) protective coating". Sheet vinyl, the kind that comes off a roll, works on the same idea. Forbo describes its Novilon cushion vinyl as having "a strong protective finish".
Once that clear layer wears through, there's nothing left to clean back, which is why harsh products and abrasive pads matter so much. It also means your first job is finding out whose floor you've got. Check the fitter's invoice or the guarantee paperwork for the brand, because that tells you which care guide to follow.
How to clean LVT flooring day to day
This routine follows Forbo's floorcare guide for its Allura LVT. Karndean and Amtico say much the same, apart from vacuuming (step 2) and a few quirks covered below.
- Get the grit up first. Soft broom, dust mop or vacuum. Grit underfoot is what scratches the surface.
- Vacuum with care, if at all. Forbo says to check nothing sharp is in contact with the floor, because it can get stuck under the vacuum and scratch it. Amtico goes further and advises against vacuuming its floors, especially with a heavy upright, because grit gets trapped under the base. It suggests a dust mop, then a dustpan and brush or a handheld vacuum for the debris. Karndean says to check with your vacuum's maker that it's suitable for a Karndean floor.
- Use a pH-neutral cleaner at the label dilution. Forbo specifies pH 7 to 8 and says "Never use undiluted solutions." A stronger mix doesn't clean better. It just leaves more behind.
- Damp mop, don't flood it, then rinse. "Do not over wet the floor when cleaning" is the first line of Forbo's general advice. When Forbo's routine uses a cleaning solution, it finishes with clean water and a mop.
- Keep the water clean. Rinse the mop often and change the water when it looks grey, or you're just spreading dirt evenly. It's the same habit that turns tile grout dark.
- Let it dry. Forbo says not to put loose rugs or mats back until the floor is completely dry.
Wipe spills straight away, especially fats, grease and anything that stains (Forbo's example is tomato sauce). Forbo also warns that unglazed pottery bases can stain the floor, so don't stand plant pots straight on it.
How often? Forbo says it depends on "the required cleanliness, intensity of use and the colour". Amtico is more specific: sweep daily, damp mop weekly.
How to clean Karndean floors
Karndean keeps it simple: a soft broom, a damp mop and a pH-neutral cleaner. Its UK help pages are short and fairly strict.
| Topic | What Karndean says |
|---|---|
| Everyday cleaning | Soft broom, damp mop and a pH-neutral cleaner such as Karndean Clean |
| Bleach | Avoid products containing agents such as bleach, which could damage the floor |
| Steam mop or steam cleaner | Not recommended |
| Furniture | Felt pads under legs, no dragging, load-bearing castors for heavy items such as washing machines |
| Black scuff marks | A little Karndean Clean diluted in water, on a damp cloth or non-abrasive scouring pad |
| Light scratches | Karndean Remove with a non-abrasive pad, then Karndean Refresh to restore the satin finish |
| Deep scratches | Try Remove and Refresh first. If the scratch persists, ask your fitter about replacing the plank |
Source: Karndean UK, Help and FAQs
Karndean's cleaning and care page suggests extra care "once or twice a year" with Remove and Refresh, and warns that household cleaners and bleach-based detergents can make the floor slippery or discolour it. It also says scuffs from shoes or furniture can be buffed out with a tennis ball, which is about the cheapest fix in this guide.
On doormats, Karndean says natural latex or polypropylene backings are compatible, but man-made backings (PVC and many synthetic rubbers) may cause discolouration over time.
How to clean Amtico floors
Amtico wants a weekly damp mop with a traditional string mop and wringer bucket, worked backwards towards the door in an S shape.
| Topic | What Amtico says |
|---|---|
| Day to day | Dust mop, or sweep with a soft brush |
| Mopping | Damp mop weekly with Amtico Maintainer at the label dilution. Rinse and wring the mop often |
| Products | Only Amtico maintenance products. Others "may lead to inferior results or leave harmful residues" |
| Steam | Do not use steam cleaners |
| Rubber | Avoid contact with rubber, such as mats or furniture bases |
| Furniture | Felt pads or glides, and castor cups to spread heavy loads. Lift, don't drag |
| Spills | Wipe up straight away. Fats or grease can make the floor slippery |
| Deep clean | Amtico Stripper: mop on liberally, leave 10 minutes, agitate, then mop off with fresh water |
Source: Amtico, wear and care leaflet for Signature, Spacia, Form, First and Click Smart (PDF)
Two answers on Amtico's cleaning advice page catch people out. Bleach is allowed if it's "properly diluted one part bleach to ten parts water", the opposite of Karndean's line. Vinegar isn't, because "the acidity can dull the surface of the floor". If you've been mopping with a vinegar mix because a website said so, that could be your dull floor right there.
Two LVT makers, opposite answers on bleach. That's why generic vinyl cleaning advice falls down, and why your maker's guide beats any blog post, this one included.
What ruins LVT and vinyl flooring
Straight from the makers' "don't" lists:
- Steam. All three say no. Amtico's cleaning and maintenance FAQ says "the intense heat may damage the tiles or cause adhesives to fail."
- Abrasive powders and scouring pads. Forbo says never to use them. When Karndean and Amtico suggest a pad for marks, it's a non-abrasive one.
- Rubber-backed mats. Amtico says "they can permanently stain LVT", and permanent means cleaning won't move it. Karndean accepts natural latex backings, but Amtico's Safety LVT guide says to avoid latex-backed mats too.
- Soap, solvents and harsh chemicals. Forbo says soap-based products, solvents and highly acidic or alkaline solutions "should not be used", and specifically rules out "strong solvents such as acetone for stain removal".
- Polish overspray. Amtico and Forbo both warn that silicone overspray from furniture polish can make the floor slippery.
- Too much water. Forbo says don't over-wet the floor when cleaning. Karndean says its floors cope with surface water, but water and other liquids make them slippery, so mop damp and let the floor dry.
Why is my vinyl floor dull, grey or sticky?
A vinyl floor that looks cloudy the day after mopping, or feels tacky underfoot, may be wearing a film of old cleaner rather than dirt. Residue can be rinsed off, though a soap film can take more than one go.
Forbo's floorcare guide for its Novilon sheet vinyl is frank about it: "overuse or inadequate rinsing of cleaning solutions may compromise the performance of the floor." For a floor that seems slippery, it says to remove "all traces of surface contamination, including detergent residues" and rinse thoroughly with clean water.
The usual culprits:
- Too much product. Amtico's Safety LVT guide warns that too high a concentration "may leave a surface residue".
- Washing-up liquid or soap, which Amtico says may leave a hard-to-remove film that detracts from the appearance.
- Vinegar, which Amtico says can dull the surface.
- One bucket of dirty water spread across every room.
- Old polish or dressing that's never been stripped. Amtico's Dressing is "designed to be stripped periodically", taking minor marks and scuffs with it. That's why a tired vinyl floor often just needs the old polish stripped, not anything aggressive.
Grey lanes in a hallway or in front of the sink can be ground-in soil, or scuffs and fine scratches from grit. Amtico says stripping restores the finish "by removing marks and scuffs in the wear layer", so scuffing isn't always for keeps.
Before buying anything stronger, try a clean-water rinse with a well-wrung mop, changing the water every room or so. If the floor dries brighter, residue was the problem, and from now on it's the label dilution and not a drop more.
How to deep clean vinyl and LVT floors
Deep cleaning vinyl means taking off the residue and old finish that have built up, then rinsing it all away. It doesn't mean scrubbing harder.
For homes, each maker has its own version:
- Karndean: Remove, then Refresh, once or twice a year.
- Amtico: a deeper clean once a year with Amtico Stripper, left about 10 minutes, agitated with the mop or a soft brush, then mopped off and rinsed with fresh water. A Matt or Satin Dressing can go on afterwards.
- Forbo: a periodic clean with its recommended cleaner and a clean-water rinse, plus a pH-neutral maintainer when the surface looks dull.
Use whatever your maker recommends for this step.
A mop runs out of road on a big floor, or on vinyl that's had years of polish layered on. That's where a machine clean comes in. We use a rotary machine with vacuum recovery, which agitates the surface and removes the water and the soil together. On vinyl, the fix is often just stripping the old polish. Landlords can book it alongside an end of tenancy clean.
Safety flooring in offices, shops and hallways
If your office, shop or communal hallway has safety vinyl, the rules get stricter. This is Amtico's guidance for its Safety LVT range:
| Task | What Amtico says for Safety LVT |
|---|---|
| Mopping | Two-bucket system and a damp mop, with Amtico Maintainer or equivalent at the label dilution |
| Scrubber dryers | Pads no more abrasive than a red 3M pad, at no more than 180rpm |
| Buffing | Never spray or dry buff. Buffing machines should never be used |
| Deep clean | At handover, then every six months to a year depending on location |
| Floor dressings | Never. They could compromise the performance of the floor |
| Mats | Avoid rubber or latex backed mats, which may leave stains |
| Products | Soap or washing-up liquid may leave a hard-to-remove film. Too strong a mix may leave a residue |
Source: Amtico, Safety LVT Maintenance Guidelines (PDF)
Some safety flooring is deliberately textured, and Amtico says its safety floors should never be dressed, so clean but not glossy is the honest result. Anyone running a machine on an Amtico Safety floor should know those limits before they start: scrubber dryers only, at 180rpm or less, nothing harsher than a red pad, and no buffing machines. We do commercial floors out of hours, and they can go in with an office deep clean.
When cleaning can't fix it
Some damage isn't dirt, and no clean brings it back:
- Worn-through pattern. Amtico defines wear out as "the removal of the pattern and colour from an Amtico floor, caused by the removal of the protective wear layer."
- Deep scratches, where Karndean's last resort is asking your fitter about a new plank.
- Rubber mat stains, which Amtico calls permanent.
- Tiles lifting after steam, since Amtico warns steam can make adhesives fail. That's a fitter's job.
Stone is a different story, covered in our guide to restoring marble floors. With vinyl, prevention is the whole game: keep the grit and the wrong products off it.
Frequently asked questions
Can you use a steam mop on LVT flooring? Not on Karndean, Amtico or Forbo floors, because all three advise against steam. For another brand, check its care guide and assume no until it says yes.
What is the best thing to clean LVT floors with? A pH-neutral cleaner made for vinyl, diluted as the label says, on a well-wrung mop. Amtico recommends using only its own maintenance products on its floors.
Can you use bleach on vinyl flooring? It depends on the brand. Karndean says to avoid it, while Amtico allows one part bleach to at least ten parts water. If you don't know who made your floor, leave it out.
Can I use vinegar to clean LVT? Amtico says no, because the acidity can dull the surface, and Forbo says highly acidic cleaning solutions shouldn't be used on its vinyl.
Why does my vinyl floor look cloudy after mopping? It can be residue from too much cleaner, a soap-based product or not enough rinsing. Rinse thoroughly with clean water, as Forbo advises for detergent residue, then go back to the label dilution.
When to get help
Get someone in when the routine has stopped working, say the floor still looks grey or tacky after a careful rinse, or there's years of old polish on it. A commercial floor that has to stay open during the day is the other obvious case.
We machine clean and strip vinyl and LVT floors alongside tile, stone and sealed concrete, priced as a one-off restoration rather than a contract. Send a few photos on WhatsApp, with the brand if you know it. If they show worn-through pattern, you need a fitter, not a cleaner.
Get a free, no-obligation quote, call 07375 104665, or WhatsApp wa.me/447375104665. We cover North London and the Hertfordshire borders.
Last updated: 2 November 2026
About Techno Clean: a London deep-cleaning company covering North London and the Hertfordshire borders. We specialise in one-off deep cleans for homes, landlords, builders and businesses, fully insured with £5 million public liability cover, with more than 500 jobs completed.




